New Holland W80C HS

CroppedImage500278-NH-W80CHS-2015.jpg

Compact Wheel Loaders W80C HS

 

PRECISE CONTROL AND LOAD PLACEMENT

New Holland compact wheel loaders provide a combination of increased versatility, increased comfort and control so you get the job done more quickly and efficiently. SMART precise load control and speed control improves operating efficiency. And these wheel loaders do much more than load. With big engine and hydraulic power and a choice of buckets and attachments, you can scrape, grade, haul and more.

Model W80C HS
DIMENSIONS, in. (mm)  
Cab height 106” (2680)
Wheelbase 88” (2225)
Ground clearance under shaft 19” (493)
Ground clearance under axles 15” (370)
Angle of departure 32°
Overall width without bucket 73” (1860)
Tread width 59” (1500)
Operating height - fully raised with spillgaurd 169” (4322)
Hinge pin height - fully raised 132” (3395)
Overall length - bucket level on ground 222” (5684)
Dump height - fully raised, 45° dump 105” (2687)
Bucket reach - fully raised, 45° dump 33” (845)
Bucket reach - 7 ft 0 (2.13m), 45° dump 52” (1323)
Dig Depth 3” (84)
Turning radius - outside 157” (3987)
Turning angle: From center 40°
Turning angle: Total angle 80°
Rear axle oscillation, total 20°
ELECTRICAL  
Voltage, volts 12
Alternator, amps 120
Batteries 95 AHR, 900 CCA
HYDRAULICS  
Pump (steering/implement) Open-centered pressure/flow compensated. Fixed gear pump
Loader control valve Open-center, Hydraulic Loader Control with single lever includes: Forward/Neutral/Reverse switch, Floating switch, Low/High Travel mode switch, Auxiliary Function Roller
Loader auxiliary steering Hydraulic orbital center-pivot articulating w/on-demand oil flow
Filtration 15-micron, full flow replaceable cartridges on return line
Flow at 2500 rpm, gpm (lpm) 22 (85)
Main relief pressure, psi (bar) 3335 (230)
HIGH FLOW  
Pump Additional HF pump
Flow at 2500 rpm, gpm (lpm) 34 (130)
Pressure, psi (bar) 2900 (200)
CYLINDERS  
Lift cylinder(s) two
Bore diameter, in (mm) 3 (84)
Rod diameter, in (mm) 2 (51)
Stroke, in (mm) 30 (751)
Dump cylinder: Bore diameter, in (mm) 3 (89)
Dump cylinder: Rod diameter, in (mm) 2 (57)
Dump cylinder: Stroke, in (mm) 20 (507)
ENGINE  
Model F5HFL463A*F004
Type 4-stroke
Cylinders 4 cylinders
Fuel injection High pressure common rail injection
Fuel Diesel
Fuel Filter Replaceable, full flow
Air filter Dry type element w/ warning restriction indicator
Radiator Core type Staggered
Fan Direct drive
Lubrication/cooling oil pump integral
Engine oil SAE 10W40 CJ-4 DIESEL/SAE 0W40 CJ-4 DIESEL
Pump Deep sump plate cooler with pressurized under-piston nozzles
Bore, in. (mm) 3.898 (99)
Stroke, in. (mm) 4.33 (110)
Displacement, liters 3
Pump operating angles: Side-to-side Rated 35°
Pump operating angles: Fore and aft Rated 35°
Oil filtration Replaceable, full flow
Engine speed: Rated speed, full load, rpm 2500
Engine speed: Low idle, rpm 950
Engine speed: High idle, no load, rpm 2500
Horsepower - @ 2500 rpm: Gross, hp (kW) 74 (55)
Horsepower - @ 2500 rpm: Net, hp (kW) 70 (52)
Peak torque @ 1400 rpm: Gross, lb ft (N·m) 233 (316)
Peak torque @ 1400 rpm: Net, lb ft (N·m) 227 (308)
DRIVETRAIN  
Transmission Hydrostatic transmission
Planetaries Outboard
Pump relief, psi (kPa) 6 (42)
Pump flow @ 2500 rpm, gpm (L/min) 37 (140)
Differential Open Diff or LSD or 100% Diff Lock
Front axle: Differential ratio 3.67
Front axle: Planetary ratio 6
Front axle: Final axle ratio 22
Gear box: 1st ratio 2.75
Gear box: 2nd ratio 1.163
Service brakes Single pedal. Not assisted, Hydraulic Brake pump with control of the “Inching” function. Auto refill system with auxiliary fluid tank. Caliper on front axle
Parking brake Mechanical control lever, Single dry disk on input of the front axle, Mechanical Caliper with no auto wear adjustment
TRAVEL SPEEDS, mph (km/h)  
Turtle: Forward 3 (5)
Turtle: Reverse 3 (5)
Rabbit: Forward 9 (14)
Rabbit: Reverse 9 (14)
High speed - Turtle: Forward 3 (5)
High speed - Turtle: Reverse 3 (5)
High speed - Rabbit: Forward 21 (33)
High speed - Rabbit: Reverse 21 (33)
SERVICE CAPACITIES  
Fuel tank, gal (l) 23 (87)
Hydraulic system: Total, gal (l) 15 (57)
Hydraulic system: Reservoir, gal (l) 11 (40)
Hydraulic system: Front Axle, gal (l) 2 (9)
Hydraulic system: Rear Axle, gal (l) 3 (12)
Hydraulic system: Engine oil w/ filter, gal (l) 2 (7)
Hydraulic system: Cooling, gal (l) 3 (13)
OPERATING WEIGHTS  
Reference configuration Unit Equipped with ROPS/FOPS cab with heater, standard counterweight, front and rear fenders, full fuel, 165 (75 kg) operator
Reference tires 365/80 R20 Dunlop Tires
Reference bucket 1.4 yd³ (1.0 m³) general purpose bucket w/ Bolt-on-Edge
Operating weights, lb (kg) 13,184 (5980)
With optional counterweight, lb (kg) 13,514 (6130)
FORKS  
Fork weight with V type Coupler, lb (kg) 761 (345)
Forks length, in (mm) 47 (1200)
Fork load center, in (mm) 20 (500)
Max height below forks, in (mm) 128 (3239)
Ground-Fork Clearance @ max Reach, in (mm) 55 (1398)
Payload (80% of FTTL - EN 474-3), lb (kg) 5011 (2273)
Tipping load - straight, lb (kg) 7372 (3344)
Tipping load - 40° turn, lb (kg) 6266 (2842)
Payload (80% of FTTL - EN 474-3) w/ add cwt, lb (kg) 5344 (2424)
Tipping load with add cwt- straight, lb (kg) 7950 (3606)
Tipping load with add cwt - 40° turn, lb (kg) 6680 (3030)
STD BUCKET  
Description 1.4 yd³ (1,0 m³) GP bucket Naked
Dump angle - fully raised 45°
Max. rollback: Ground 40°
Max. rollback: Carry Position 45°
Max. rollback: @ Maximum reach 55°
Max. rollback: @ Full height 55°
Maximum back dragging angle 61°
ISO bucket capacity - Struck, yd3 (m3) 1.2 (0.8)
Heaped, cu. yd. (m3) 1.4 (1.0)
Bucket width - outside, in (mm) 82 (2100)
Bucket weight (incl. Coupler and components), lb (kg) 926 (420)
Operating load - ISO, lb (kg) 3962 (1797)
Maximum material density - ISO, lb/yd³ (kg/m3) 3029 (1797)
Tipping load - ISO: Straight, lb (kg) 9517 (4317)
Tipping load - ISO: 40° turn, lb (kg) 7921 (3593)
Tipping load - ISO: Straight with add cwt 10,031 (4550)
Tipping load - ISO: 40° turn with add cwt 8510 (3860)
Operating load with add cwt - ISO 4006 (1817)
Maximum material density with add cwt - ISO 3147 (1867)
Lift Capacity: Full height, lb (kg) 8424 (3821)
Lift Capacity: Maximum reach, lb (kg) 10,644 (4828)
Lift Capacity: Ground, lb (kg) 13,746 (6235)
Breakout force with tilt cylinder, lb (kgF) 13,927 (6317)
Loader clearance circle, in (mm) 362 (9294)

Fields with asterisks* and highlighted red are required. Please email our helpful staff with any questions or comments using the contact form.

Fields with asterisks* and highlighted red are required. Your friend will receive an email that contains a reference to this page. Please send this email only to people you know who would be interested in this information.

RANCHRITE hardware available at Western Implement